Iron sheets for the garage. Construction of metal garages, from corrugated board and sandwich panels
If you have purchased new car you probably don't want to leave it out in the open. Even paid parking is far from the best option- Precipitation has a devastating effect on the car body. However, you can install metal garage close to home and solve many problems.
To work, in addition to sheet metal, you will need shaped or ordinary pipes, profiles, insulation, cladding, fasteners, as well as cement, sand and gravel for the preparation of concrete mix.
Making the foundation and floor
Like any structure, iron garages begin to be made from the foundation. To do this, it is necessary to dig up racks in the corners of the site. At the same stage, if necessary, a viewing hole breaks out. Concrete mixture is poured inside the racks. An iron garage is installed on a concrete pad, it should be approximately 10-15 cm above the ground. The elevation will protect the room from the penetration of melt water and various precipitation into it.
In metal caravans, the floor is poured more easily than in other types of garages. The floor should not contain any defects: no bulges, no cracks, its perfect evenness should not cause any doubts. From the side of the gate have an entrance. As a rule, it will take about 2-3 cubic meters of concrete to fill the floor.
Assembling a metal garage
At the very beginning, we make the frame. To connect the vertical racks, profile slopes are used in the center, as well as the lower and upper parts of the room. The frame is preferably welded, but its connection with fasteners is allowed.
In metal garages, roofs with two slopes are made: for this, triangular profiles are installed above the ceiling. When the frame is erected, it is sheathed with sheet metal. Sheets can be screwed to the frame with screws, or they can be welded. The advantage of a prefabricated garage is that it can be quickly dismantled and reinstalled elsewhere.
Manufacturing garage doors
We have already considered how to install a metal garage. The next stage of work is the manufacture of its gate. For the construction of the frame for them, corner metal is used, which is welded to the garage racks and sheathed with a sheet. As a rule, gates are made at least 2.5 meters wide.
It is important to choose and install the right locks. For increased security, use two locks - the main one and the one that will block access to it. The simplest type of gate for an iron garage is swing.
Construction insulation
After the construction of the garage, it must be insulated. The metal has a high thermal conductivity, so it will quickly heat up in the sun and cool in winter. As a heat-insulating material, glass wool, polystyrene and other heaters can be used.
For metal garages mineral wool would be a suitable option. It differs in fire resistance and good heat-shielding characteristics. Of course, you can save money and use foam. Although it allows self-extinguishing, it is still a combustible material.
High-quality thermal insulation will help create suitable conditions for storing a car. The heat insulator is covered with sheathing. It can be ordinary iron, which is treated with a primer, as well as corrugated board. Often, fiberboard, PVC, chipboard or wood are used as finishes for iron garages.
So, we looked at how to make and insulate a metal garage with our own hands. By adhering to these recommendations and the sequence of work, you can get a reliable design that will protect your car from theft and bad weather.
Garages
For vehicle owners, the main tasks are to ensure the smooth operation of the car, and to organize suitable conditions for parking the car. In many ways, the performance of the car depends on the conditions in which the car is left overnight, or is in a long parking lot. This question is especially relevant, who prefers winter period do not use your own transport, or for people who often go on long business trips. In the open air, the car is constantly exposed to the sun, precipitation, low and high temperatures, and many other factors. Naturally, such impacts have a detrimental effect both on the paintwork of the body and on the correct operation of the machine as a whole.
The construction of a garage will allow the poor owners to get rid of many difficulties at the same time, associated not only with the safety of the car, but also with the storage of spare car parts and parts of small and overall dimensions. A garage, made in accordance with established standards and using quality materials, can be an excellent additional mini-warehouse for storing preserves, pickles and a variety of inventory. Thus, a significant amount of space in the apartment or in the house will be freed up.
When deciding on the choice of a garage, it must be remembered that the cost and time of construction of the structure depend on the material chosen. Brick and concrete are great for solid garages, but the construction time frame and the price of materials will not suit everyone. In addition, collection permits to permit the construction - the process is quite nervous and lengthy. Against this background, metal garages look most advantageous, which recent times became very popular and in demand. Modern construction methods make it possible to produce such structures in a matter of days, and in terms of durability they are not inferior to capital structures.
It is worth saying that not everyone can build a metal garage with their own hands. To do this, you need not only to understand the manufacturing processes of such structures, but also to choose the best metal option that is most suitable for your region. And if you do not have the necessary knowledge in this area, then the best and correct option- entrust the manufacture of metal garages to professional craftsmen. A conscientious company will not only guarantee to fulfill all obligations in full, but also provide a solid warranty period for the installed garage.
Production of metal garages
Our company has been engaged in the production and sale of metal structures of varying complexity for a long time. In this direction, we have achieved significant success, and we continue to actively develop our production. For the manufacture of metal garages of various configurations, we have at our disposal modern and technological equipment. That gives us the opportunity to implement any projects. The staff, from managers to the installation team, are qualified specialists, each in their field.
We offer to buy a metal garage at the manufacturer's price, bypassing trading margins. At the same time, the quality of manufacturing is strictly controlled in production and is carried out in full compliance with the technologies. Before sending the garage to the customer, it undergoes a control assembly, so even the smallest defect is completely excluded.
To create frames, we use galvanized steel profiles, which are made from a high-quality alloy. To create walls, corrugated board or a sandwich panel is most often used, it is worth noting that both materials have excellent technical characteristics.
You can get acquainted with our range of garages in the electronic catalog, which contains complete information regarding the dimensions and the steel used. And also choose the right complete set of the garage, depending on your wishes. Here you will find a variety of models, both in design and size. If your family has more than one car, then take a closer look at two-section garages. Exit gates can be selected with different opening methods. And this is not all the privileges that you can enjoy.
For our customers, it is proposed, if necessary, to insulate a metal garage modern materials. Also, our specialists can carry out the installation of a metal garage with operational professionalism. If you order a full range of services, from production to installation of a garage, you are guaranteed to acquire a practical and multifunctional design for at least several decades.
Advantages of our metal garages
- Large selection of proposals - We offer a wide range of ready-made models of garages of various shapes and sizes. Thanks to this variety, car owners will not have any complications with choosing the best option. Also, we carry out individual orders according to exclusive drawings.
- Multifunctionality and practicality - In an insulated garage, you can make an impromptu hozblok and store various edible preparations in it. In addition, now all spare parts and tires will not take up space in the house, all car accessories can be placed in the garage on racks.
- Fire safety - Metal is not a combustible material, so an iron garage, by definition, is not a source of fire propagation. It is considered an ideal place for storing flammable liquids and other products intended for cars.
- Light foundation - Due to the light weight of garages, such structures can be installed on concrete base 20 cm thick. Therefore, there is no need to spend a lot of time and Money for the construction of a capital foundation.
- Installing a garage in 1 day - Given the fact that these structures do not need to be poured into a capital foundation, our company will be able to install a metal garage within one day.
- Acceptable cost - Metal garages of our company are made in our own production, which allows us to sell metal structures at manufacturer's prices.
- Reliability and durability - The metal that we use in production is of sufficiently high quality, which is additionally processed with a protective coating. Given this fact, the garages of our company are suitable for operation even in the most severe climate. At the same time, the risk of corrosive plaque formation is reduced to zero, since the protective coating perfectly protects the steel from the effects of any type of precipitation.
- Low Heat Loss - Sandwich panel garages are excellent at retaining heat in the garage in the winter. At very low temperatures the garage space can be heated with a compact heater for half an hour.
- aesthetic appearance- After installing the garage, you can immediately start using it, since the interior and exterior decoration of the structure does not require additional facing work. Garages of our company look solid and presentable.
- Long service life - Even with the constant use of the garage, the structure throughout the entire period of operation will cope with its functional purpose, without bringing any difficulties to its owner.
Structural differences of metal garages
According to the type of construction, metal garages are classified into two categories:
- Welded;
- collapsible;
The decision on the choice of the type of construction remains with the customer. And in order to choose the most optimal option, you should familiarize yourself with the differences and features of these structures.
Welded metal garages
The main difference between such models is the method of assembling the frame, or rather its fastening. In this case, the frame is assembled into a solid structure by welding. It is very important that welding work be carried out by experienced craftsmen, otherwise the frame may not withstand the loads exerted on it, which will lead to distortion or destruction of the garage as a whole. If the welds were performed at the proper level, then the metal garage of the welded structure will serve its owners for the entire period of operation. Such models of garages are very reliable, but are designed for installation in one place. And if it becomes necessary to transfer the garage to another place, then it will not be possible to disassemble it without damage. The only option is to transport the structure in assembled form, which means the involvement of special equipment and crews. Which will entail quite a large cash outlay. Therefore, when choosing such structures, it is necessary to take into account the duration of the use of the garage in one place.
Collapsible metal garages
Due to mobility, these designs are in great demand in the market. The peculiarity lies in the fact that the frame is assembled into a single structure with the help of connecting elements, self-tapping screws and similar items. What makes it possible to disassemble the garage for rearrangement to another place. Welding can only be used to install exit gates, but this nuance will depend on the choice of model. It should be noted that the installation of a metal weed garage can be carried out in one day.
Types of metal garages
To date, the market is full of proposals for the purchase of garages, the cost of which is very different. The most budget option is to use sheet steel for the walls of the garage. But this material has a significant drawback, it is not initially protected by an anti-corrosion coating. Therefore, the service life of the garage is significantly reduced, and is no more than 20 years. Based on this, we can draw an unambiguous conclusion - a cheap metal garage does not have long-term operation. In our company, all offered garages have an anti-corrosion coating, regardless of the steel used, which can significantly increase the service life of the contraction.
A more expensive, but more reliable option is to make garage walls from corrugated board. This material has high strength indicators and perfectly resists all types of precipitation, as well as mechanical stress. A special protective coating prevents the formation of a corrosive coating, while the corrugated surface gives the entire structure an additional margin of safety. Thus, it becomes clear that corrugated metal garages will last much longer than sheet steel.
Special attention deserves a metal garage made of sandwich panels, as an innovative and modern solution for the manufacture of structures using high-tech materials. The sandwich panel is assembled according to the principle of a sandwich, where there is a heater between two steel sheets. As a heater, only modern eco-friendly materials that are incombustible are used. Garages made of sandwich panels do not need additional insulation, as they perfectly retain heat indoors. Durability and strength are not inferior to corrugated board, for this reason this material is very popular in the construction environment.
Why choose us
We value our customers and reputation, offering exceptionally reliable designs with a maximum warranty period. Here are just a few reasons why you should choose us:
- Own production and the ability to fulfill exclusive orders;
- Quality control of materials;
- Compliance with technological standards;
- Responsible approach to work and to each client;
- Providing comprehensive services, from manufacturing to installation of turnkey garages;
- Qualified employees with many years of experience;
- Prices from the manufacturer;
We do not promise, but guarantee the fulfillment of all obligations in full to our customers. And we can say with confidence that by contacting us, you will become a satisfied owner of a brand new metal garage in the shortest possible time. One that will last forever!
Metal garages have been used for parking and storing cars for many years.
Manufacturing metal garages and their sale is one of the main activities CRATEMET.
Any person who has a car thought about its reliable storage, and this thought visits him daily, to solve this problem, we offer metal garages according to the dimensions you need, with the possibility of assembly and installation on your territory. Our metal garages not only protect vehicles from thieves and hijackers, but also protect the car from the effects of precipitation. Metal garages from CRATEMET can also be used to store various things, spare parts. If you are an entrepreneur and a happy owner metal garage from CRATEMET, this garage can be equipped for a car repair shop or tire fitting. Metal garages can also be rented out.
metal garage refers to a free-standing structure that can be manufactured directly on the territory or object of the customer. Metal garages can be carried out in full factory readiness and are delivered ready-made.
Factory CRATEMET offers the production of prefabricated metal garages, which, if necessary, can be disassembled into components and transported to a new site. Prefabricated components metal garages are connected using conventional bolts and, if fasteners are lost, can be restored without problems. The sealing of the structure is carried out using sealants.
Metal garages made of profile metal pipe and corner. The frame of the metal garage is covered with soil. A metal corrugated board is attached to the frame of a metal garage. Metal decking can be polymer coated(RAL color) or galvanized.
We can also offer insulated metal garages.
Metal garages have a single-pitched or double-pitched roof, depending on the wishes of the Customer. Atmospheric precipitation has a natural runoff due to the slope of the roof. The roof can be made of metal corrugated board with a polymer coating (RAL color) or galvanized steel, the seams are sealed with sealants. metal garage roof It is designed with a margin of safety and will withstand snow loads without problems.
metal garage It has hinged gates (double-leaf) and a wicket, providing free entry of the car into the garage, as well as free access for a person.
Dimensions of metal garages.
The cost of metal garages with swing gates (double-leaf) and a gate, see the price list.
We also offer the construction of parking lots and garage complexes with polycarbonate roofing, we have experience working with government organizations and institutions.
We can offer garages - standing in a row, these are the most economical garages with side walls and a shed roof.
In the range of our products there are special collapsible prefabricated carports.
If you need custom size garage- managers and specialists of our company in as soon as possible calculate the cost of production and installation of a metal garage according to your size, it is also possible production of metal garages for several cars.
A metal garage is the second most important building on your site. Our company specializes in the manufacture of prefabricated metal garages. Trust the professionals and the result will not disappoint you. The right metal garages at the right prices. Delivery. Assembly. Individual approach.
Description of the construction of a metal garage.
The design of a metal collapsible garage is assembled from panels made of a sheet with a thickness of 1.5-2.0 mm st. 3 and units in full factory readiness for installation at the installation site.
Wall panels assembled with piping elements, trusses and roofs form a single rigid structure that does not require an additional reinforcing frame. This product is designed for a long service life. The variant with a shed roof can be made with a roof slope forward, backward, sideways.
The design of the metal garage is collapsible. It can be installed without a foundation. In the base, a metal garage is supplied with a protective coating - primer GF-021 red-brown (gray). Swing gates 2.5 m or 3.0 m wide.
At the request of the Customer, the prefabricated garage gate can be made in the gate leaf and / or the side (end) panel of the garage. Entrance gate height (typical 2.1 m and 2.4 m). It is possible to increase the height of the metal garage to increase the passage height to 3.0 m. installation instead of swing gates; installation of additional gates, etc.
As a material for the roof, a sheet with a thickness of 1.2 mm or a galvanized profiled sheet with a thickness of 0.7 mm is used. If metal garages are installed as a group, flat roof garages are used with or without a common side wall, if necessary.
The length of standard structures is 6.0 m. Width - 3.0m / 3.5m / 4.0m / 5.0m. Height-2.66m/2.89m.
Installation of typical prefabricated garages takes about 5-6 hours.
Design and manufacture of prefabricated metal garages is possible according to the individual dimensions of the Customer, taking into account the shape of the site (any configuration).
The cost of any metal structures is negotiable and is determined after receiving the application and agreeing on the main parameters and requirements for the structure.
Specifications.
- Width: 3000 mm.
- Length: from 6000 to 10000 mm.
- Gate opening width: 2500 mm.
Additional options:
- Gate - 4500 rubles.
- Mortise lock - 1000 rubles.
Garage length (mm) | ||||||||
6000 | 6500 | 7000 | 7500 | 8000 | 8500 | 9000 | ||
Entrance height (mm) | 2100 | 125350 | 136850 | 147200 | 158700 | 169050 | 180550 | 190900 |
2400 | 127650 | 138000 | 149500 | 161000 | 171350 | 182850 | 193200 |
Specifications.
- Width: 3500 mm.
- Length: from 6000 to 10000 mm.
- Entry height: 2100 mm, 2400 mm.
- Gate opening width: 3000 mm.
- Wall panel metal thickness: 1.5mm, 2.0mm.
- Gate panel metal thickness: 2.0 mm.
- Roofing: corrugated board C21 0.7 mm.
- Colour: grey, reddish brown.
Additional options:
- Gate - 4500 rubles.
- Mortise lock - 1000 rubles.
- Wall bracket - 300 rubles / piece.
- Painting in color - 80 rubles / m 2.
- Delivery - 30 rubles / km (in Moscow free of charge)
- Assembly - 10% of the cost of the product.
The cost of a metal garage (rub).
Garage length (mm) | ||||||||
6000 | 6500 | 7000 | 7500 | 8000 | 8500 | 9000 | ||
Entrance height (mm) | 2100 | 131100 | 142600 | 154100 | 165600 | 176000 | 187500 | 199000 |
2400 | 135700 | 148400 | 159900 | 171400 | 182900 | 194400 | 205900 |
Specifications.
- Width: 4000 mm.
- Length: from 6000 to 10000 mm.
- Entry height: 2100 mm, 2400 mm.
- Gate opening width: 3000 mm.
- Wall panel metal thickness: 1.5mm, 2.0mm.
- Gate panel metal thickness: 2.0 mm.
- Roofing: corrugated board C21 0.7 mm.
- Colour: grey, reddish brown.
Additional options:
- Gate - 4500 rubles.
- Mortise lock - 1000 rubles.
- Wall bracket - 300 rubles / piece.
- Painting in color - 80 rubles / m 2.
- Delivery - 30 rubles / km (in Moscow free of charge)
- Assembly - 10% of the cost of the product.
The cost of a metal garage (rub).
Garage length (mm) | ||||||||
6000 | 6500 | 7000 | 7500 | 8000 | 8500 | 9000 | ||
Entrance height (mm) | 2100 | 142600 | 155300 | 167900 | 179400 | 192100 | 204700 | 217400 |
2400 | 148400 | 161000 | 172500 | 185200 | 197800 | 210500 | 222000 |
Specifications.
- Width: 4500 mm.
- Length: from 6000 to 10000 mm.
- Entry height: 2100 mm, 2400 mm.
- Gate opening width: 3000 mm.
- Wall panel metal thickness: 1.5mm, 2.0mm.
- Gate panel metal thickness: 2.0 mm.
- Roofing: corrugated board C21 0.7 mm.
- Colour: grey, reddish brown.
Additional options:
- Gate - 4500 rubles.
- Mortise lock - 1000 rubles.
- Wall bracket - 300 rubles / piece.
- Painting in color - 80 rubles / m 2.
- Delivery - 30 rubles / km (in Moscow free of charge)
- Assembly - 10% of the cost of the product.
The cost of a metal garage (rub).
Garage length (mm) | ||||||||
6000 | 6500 | 7000 | 7500 | 8000 | 8500 | 9000 | ||
Entrance height (mm) | 2100 | 155300 | 169100 | 181700 | 195500 | 208200 | 222000 | 235800 |
2400 | 161000 | 173700 | 187500 | 201300 | 213900 | 227700 | 241500 |
Specifications.
- Width: 5000 mm.
- Length: from 6000 to 10000 mm.
- Entry height: 2100 mm, 2400 mm.
- Gate opening width: 3000 mm.
- Wall panel metal thickness: 1.5mm, 2.0mm.
- Gate panel metal thickness: 2.0 mm.
- Roofing: corrugated board C21 0.7 mm.
- Colour: grey, reddish brown.
Additional options:
- Gate - 4500 rubles.
- Mortise lock - 1000 rubles.
- Wall bracket - 300 rubles / piece.
- Painting in color - 80 rubles / m 2.
- Delivery - 30 rubles / km (in Moscow free of charge)
- Assembly - 10% of the cost of the product.
The cost of a metal garage (rub).
Garage length (mm) | ||||||||
6000 | 6500 | 7000 | 7500 | 8000 | 8500 | 9000 | ||
Entrance height (mm) | 2100 | 171400 | 185200 | 200100 | 215100 | 230000 | 245000 | 258800 |
2400 | 176000 | 192100 | 207000 | 222000 | 236900 | 251900 | 266800 |
Specifications.
- Width: 5500 mm.
- Length: from 6000 to 10000 mm.
- Entry height: 2100 mm, 2400 mm.
- Gate opening width: 3000 mm.
- Wall panel metal thickness: 1.5mm, 2.0mm.
- Gate panel metal thickness: 2.0 mm.
- Roofing: corrugated board C21 0.7 mm.
- Colour: grey, reddish brown.
Additional options:
- Gate - 4500 rubles.
- Mortise lock - 1000 rubles.
- Wall bracket - 300 rubles / piece.
- Painting in color - 80 rubles / m 2.
- Delivery - 30 rubles / km (in Moscow free of charge)
- Assembly - 10% of the cost of the product.
The cost of a metal garage (rub).
Garage length (mm) | ||||||||
6000 | 6500 | 7000 | 7500 | 8000 | 8500 | 9000 | ||
Entrance Technical characteristics. | ||||||||
6000 | 6500 | 7000 | 7500 | 8000 | 8500 | 9000 | ||
Entrance height (mm) | 2100 | 211600 | 230000 | 248400 | 266800 | 285200 | 302500 | 320900 |
2400 | 223100 | 239200 | 255300 | 279500 | 294400 | 312800 | 333500 |